Skip to content

3/4 npt tap drill size

NPT Tap Drill Reference

3/4 NPT Tap Drill Size for 3/4-14 NPT

For a 3/4-14 NPT internal pipe thread, the common tap drill size is 59/64 in. This equals 0.9219 in, or about 23.42 mm. Use this page as a quick shop-floor reference before drilling and tapping a 3/4 NPT threaded port.

Quick answer59/64 in3/4-14 NPT · 59/64 in drill · 0.9219 in · 23.42 mm · 14 TPI
HSS NPT pipe tap for 3/4 NPT threaded port drilling and tapping
Specification

3/4-14 NPT Tap Drill Specification

ItemValueMachining Note
Thread callout3/4-14 NPTNational Pipe Taper thread.
Tap drill size59/64 inCommon shop reference before tapping 3/4 NPT.
Decimal inch0.9219 inUse this value when checking drill chart or CNC setup notes.
Metric equivalent23.42 mmApproximate metric conversion.
Threads per inch14 TPIDo not confuse with straight fastener threads.
Tap type3/4-14 NPT pipe tapUse an NPT pipe tap, not a UNC/UNF straight-thread tap.
Important: 3/4 NPT is a tapered pipe thread. The nominal pipe size does not mean the drilled hole uses the same diameter. Do not use straight-thread tap drill values for this thread.
Machining Notes

How to Drill and Tap 3/4 NPT Threads

1. Drill the pilot hole

Use 59/64 in for the common 3/4-14 NPT tap drill reference. Keep the drilled hole straight and rigid before tapping.

2. Use the correct pipe tap

Use a 3/4-14 NPT pipe tap. NPT threads are tapered, so tapping depth and gauge result matter more than with many straight internal threads.

3. Verify engagement

Before batch production, verify the tapped port with the required gauge or mating fitting. Do not rely only on the drill size when sealing or assembly depth is critical.

Production note: Tapping torque increases as an NPT pipe tap goes deeper because the thread is tapered. Use suitable cutting fluid, rigid alignment and controlled tapping depth.
Comparison

Common NPT Tap Drill Sizes Around 3/4 NPT

For nearby NPT sizes, compare the common drill references below. For metric, UNC, UNF and additional NPT sizes, use the complete tap drill size chart.

NPT ThreadTPICommon Tap DrillDecimal Inch
1/4-18 NPT187/16 in0.4375 in
1/2-14 NPT1423/32 in0.7188 in
3/4-14 NPT1459/64 in0.9219 in
1-11.5 NPT11.51-5/32 in1.1563 in
Application Note

Where 3/4 NPT Threads Are Commonly Used

3/4 NPT is commonly used for larger threaded ports than 1/8 NPT or 1/4 NPT. Typical applications include valve bodies, hydraulic manifolds, air or water lines, pump connections, adapters and industrial fluid-system parts. Because the port is larger, drilling rigidity, tapping torque and thread-depth control become more important.

Valve bodies and fittings

3/4 NPT threads are often used where a larger pipe connection is required. The tapped port must match the fitting standard, not only the nominal pipe size.

Hydraulic manifolds

Manifold ports need controlled drilling, tapping depth and gauge verification. A small error in alignment or depth can affect assembly and sealing performance.

Industrial fluid lines

For air, water, oil or general fluid lines, confirm the thread standard, fitting type and sealant requirement before selecting the pipe tap and pilot hole.

Large-port warning: 3/4 NPT tapping generates more torque than smaller NPT sizes. Use rigid workholding, proper cutting fluid, controlled depth and a suitable 3/4-14 NPT pipe tap. Do not treat it like a small repair tap.
Drill Size Variation

Why 3/4 NPT Tap Drill Size References Can Vary

The common quick-reference tap drill for 3/4-14 NPT is 59/64 inch, or about 0.9219 inch. However, some machining references and shop practices may list different pilot-hole values depending on whether a taper pipe reamer is used, how the port is gauged, the material being tapped, and the required thread engagement.

Use 59/64 in as the common reference

For a standard quick lookup, 59/64 in is the practical reference value for 3/4-14 NPT tap drilling. Use the decimal or metric equivalent when checking machine setup or drill availability.

Check gauge result for production

If the tapped port must meet a specific inspection standard, use the required gauge or mating fitting to confirm engagement after tapping. NPT quality is not determined by drill size alone.

Best practice: For one-off lookup, use 59/64 in. For batch machining, drill one test port, tap to controlled depth, then verify the thread with the required NPT gauge or mating fitting before approving production.
Production Checklist

3/4 NPT Drilling and Tapping Checklist

Use this checklist before machining 3/4 NPT ports so the drill size, tap type, alignment, lubrication and final inspection are checked together.

Check PointRecommended ActionWhy It Matters
Thread standardConfirm the drawing calls for 3/4-14 NPT.NPT is a tapered pipe thread and should not be confused with straight fastener threads.
Pilot holeUse 59/64 in as the common tap drill reference.The correct pilot hole helps avoid excessive torque or weak thread engagement.
Tap typeUse a 3/4-14 NPT pipe tap.A regular metric, UNC or UNF tap cannot produce a correct NPT tapered pipe thread.
Machine setupKeep the drill and tap aligned with the port axis.Misalignment can damage the port and reduce thread quality.
LubricationUse suitable cutting fluid and clear chips carefully.Lubrication and chip control reduce torque, tearing and breakage risk.
InspectionVerify the tapped port with the required gauge or mating fitting.Final thread quality depends on both drilled hole and tapping depth.
Related Specific NPT Pages

Related NPT Tap Drill Size Pages

Use the related size references below for common NPT lookups, or open the full tap drill chart for a wider range of thread standards and sizes.

Product Selection

Choose the Correct 3/4-14 NPT Pipe Tap After Drilling

The drill size only prepares the hole. The tap still needs to match the pipe thread standard, workpiece material, hole depth and production method.

Use an NPT pipe tap when

  • The drawing calls for 3/4-14 NPT.
  • The part uses a tapered pipe-thread connection.
  • The component is a fitting, valve, hydraulic manifold, adapter or threaded port.
  • The target market uses NPT pipe thread standards.

Send these details for RFQ

  • Thread: 3/4-14 NPT or full NPT size list.
  • Workpiece material and hardness if known.
  • Port depth, thread depth and gauge requirement if available.
  • Quantity, coating preference and packaging requirement.

Need 3/4 NPT Pipe Taps?

Slugger Tools supplies HSS BSP, BSPT, NPT and NPTF pipe taps for threaded ports, fittings, valves and hydraulic manifolds. Send your size list and material details for quotation review.

View BSP / NPT Pipe TapsView HSS Thread TapsSend OEM / Bulk RFQ HereGeneral Contact
3/4 NPT Industrial Pipe Taps · OEM & Bulk Supply

Request 3/4-14 NPT Pipe Tap Specifications & Bulk Quotation

The 59/64 in (0.9219 in, approximately 23.42 mm) chart value is a common starting drill reference for 3/4-14 NPT, not a universal approved production pilot hole. Direct drilling versus taper reaming, specific tap design, workpiece material and NPT thread gauge acceptance can change process requirements. Confirm the approved drawing and maker-specific cutting data before machining.

  • Thread and inspection: 3/4-14 NPT or full BSP/NPT/NPTF size list, drawing, thread designation, acceptable gauge and taper engagement.
  • Machining: material and grade, blind or through port, usable thread depth, machine/holder, drill or taper reamer procedure, coolant and inspection approach.
  • Procurement: estimated batch or annual quantity, destination, selected HSS grade/coating, OEM branding, packaging and documentation requirements.
Please include size, material grade, coating, quantity, workpiece material, packaging requirements, and target market.

For drawings and detailed NPT size lists, email williamz@sluggertool.com or use the general contact page.

FAQ

3/4 NPT Tap Drill Size FAQ

What is the tap drill size for 3/4 NPT?

The common tap drill size for 3/4-14 NPT is 59/64 in. The decimal equivalent is 0.9219 in, or about 23.42 mm.

What thread is 3/4 NPT?

3/4 NPT is 3/4-14 NPT National Pipe Taper thread. It has 14 threads per inch and is used for tapered pipe-thread connections.

Is 3/4 NPT the same as a straight thread?

No. 3/4 NPT is a tapered pipe thread. It is not the same as a straight bolt thread and should not use straight-thread tap drill values.

What size hole should I drill for a 3/4 NPT tap?

Use 59/64 inch as the common tap-drill reference for 3/4-14 NPT. That is 0.9219 inch, or about 23.42 mm. For production work, verify the final thread with the required NPT gauge or mating fitting.

Which tap should I use for 3/4 NPT?

Use a 3/4-14 NPT pipe tap. Do not use a regular UNC, UNF or metric tap for an NPT pipe thread.